Agrowplow

Shearpin and clips for the #1 Rigid Shank Pre-1988 Assembly. The shearpin has a 25.4mm diameter and is 120mm long with a 67mm shear section. Suppli...

Shank Carrier for the #1 Rigid and Hydraulic Shank Assemblies (pre-1988/shearpin models only). See 120-0002 for the complete assembly.  Old Part No...

Helper Bar for the #7 spring jump assembly. Old Part No. 125-036001-407

Hinge plate for the #7 spring jump assembly. Old Part No. 001-302

Spring bar for the #7 spring jump assembly. Old Part No. 125-036

Clamp plate for the #8 Rigid Shank Assembly (120-0006). Mounts to 100x100mm (4x4") RHS frame. *Old Part No. 002-201

Spring jump pivot clamp to suit 100mm or 4" RHS. Suits the #8 spring jump shank models. Also known as a carrier plate. This has a 1" hole *Old Par...

Shank carrier for the #8 Hydraulic Shank Assembly. Mounts to 100 x 100mm RHS frames. *Old Part No. 005-102

82 mm shearpin to suit certain #8 Rigid Shank and #8-9 Hybrid Rigid Shank assemblies with 1,089 kg breakout force at the blade. Selecting the corre...

This 90 mm shearpin is the current standard for #8-9 Hybrid Rigid Shank 100 x 100 mm RHS assemblies fitted to AP11 and AP31 ploughs and provides a ...

92 mm shearpin to suit certain #8 Rigid Shank and #8-9 Hybrid Rigid Shank assemblies with 1,089 kg breakout force at the blade. Selecting the corre...

68 mm shearpin to suit certain #8 Rigid Shank assemblies with 1,089 kg breakout force at the blade. Selecting the correct shearpin reduces downtime...

Shinguard to suit 24" #8 Shank. This shinguard comes with additional hardfacing to reduce wear and extend the working life of the shinguard. For a ...

Shinguard to suit 24" #8 Shank. This shinguard primarily suits customers that do their own hardfacing.For a hardfaced wear-resistant shinguard, cli...

Shinguard to suit 30" #8 Shank. Available with additional hardfacing to reduce wear and extend the working life of the shinguard.  Old Part Numbers...

Hardened pin utilised on the #9 shank hydraulic recoil assembly. The 2 x 7/16" rollpins provided can be installed using the 7/16" punch. Alternate...

Suits the original #9 Hydraulic Recoil assembly (but not the #9v2). Secures the top of the cylinder with a lynch pin 140-0041 and a hairclip 141-00...

30mm diameter pin to secure the top of the hydraulic cylinder in the #9v2 shank assembly. Suits the Hydraulic Cylinder 3" Bore (153-4217).

This high-breakout #9 shearpin is supplied on request for operators who are consistently breaking the standard #9 shearpin in very hard or abrasive...

This is the standard #9 shearpin supplied and fitted to Agrowplow machines from factory. Designed to protect the frame and shank assembly by sheari...

Shear pin and clips to suit the Econo Rigid shank assembly. Fits the 4"x4" Econo Rigid Shank carrier 004-3001. *Old Part No. 141-017

Send drawing 680-4142-A

This accumulator clamp suits both 10L and 20L accumulators. Alternate Part No.154-488  

Alt. Part SKU 115-721

This hub component suits the AGR HUB 1, tapered bearing coulter hub assembly 139-4200. Stud to suit 139-4201, Nut to suit stud 139-2027. The ta...

Toolbox to be attached to a plough, contains spare parts for a plough.

Rear tow hitch for the Agrowplow AP11. A rear tow hitch enables trailing machines to be hitched to the rear of the seed drill, including the Rubber...

  The rear tow hitch allows trailing implements to be hitched safely to the rear of the ripper and provides the facility for it to be connected vi...

*Old Part No. 138-331

Two-piece bearing housing used to secure the 25.4mm spherical bearing to the Agrowdrill. Commonly found on older Agrowdrill models.The distance bet...

Bearing with ID 5/8" and OD 52mm. Mounts into 110-4112 bearing housing. *Old Part No. 138-325

Bearing with ID 5/8" and OD 52mm. Mounts into 110-4112 bearing housing. *Old Part No. 138-325

SEALED DEEP GROOVE METRIC BALL BEARINGS

Sealed bearing, fits on a shaft 25mm and into hub or housing of 62mm in diameter. ID 25mm, OD62mm. Cylindrical. *Old Part No. 138-031