Agrowplow

Shearpin and clips for the #1 Rigid Shank Pre-1988 Assembly. The shearpin has a 25.4mm diameter and is 120mm long with a 67mm shear section. Suppli...

Shank Carrier for the #1 Rigid and Hydraulic Shank Assemblies (pre-1988/shearpin models only). See 120-0002 for the complete assembly.  Old Part No...

Helper Bar for the #7 spring jump assembly. Old Part No. 125-036001-407

Hinge plate for the #7 spring jump assembly. Old Part No. 001-302

Spring bar for the #7 spring jump assembly. Old Part No. 125-036

Clamp plate for the #8 Rigid Shank Assembly (120-0006). Mounts to 100x100mm (4x4") RHS frame. *Old Part No. 002-201

Shank carrier for the #8 Hydraulic Shank Assembly. Mounts to 100 x 100mm RHS frames. *Old Part No. 005-102

Shearpin to suit the #8 and #8-9 Hybrid Rigid Shank Assemblies. Shearpins provide a substantially higher breakout than hydraulic breakout machines ...

Shearpin to suit the #8 and #8-9 Hybrid Rigid Shank Assemblies. Shearpins provide a substantially higher breakout than hydraulic breakout machines ...

Shearpin to suit the #8 and #8-9 Hybrid Rigid Shank Assemblies. Shearpins provide a substantially higher breakout than hydraulic breakout machines ...

Shearpin to suit the #8 and #8-9 Hybrid Rigid Shank Assemblies. Shearpins provide a substantially higher breakout than hydraulic breakout machines ...

Shinguard to suit 24" #8 Shank. This shinguard comes with additional hardfacing to reduce wear and extend the working life of the shinguard. For a ...

Shinguard to suit 24" #8 Shank. This shinguard primarily suits customers that do their own hardfacing.For a hardfaced wear-resistant shinguard, cli...

Shinguard to suit 30" #8 Shank. Available with additional hardfacing to reduce wear and extend the working life of the shinguard.  Old Part Numbers...

#8 Hybrid rigid 100x100 Shank Assembly with coulter assembly #8-9 Hybrid Shank Assembly AP11, AP31: PartsManual_UC_8-9HybridShank_1910

The #9 blade is unique to Agrowplow and is the superior ripping blade for your plough. This GP blade comes with 3 x heavy-duty rock teeth across th...

Hardened pin utilised on the #9 shank hydraulic recoil assembly. The 2 x 7/16" rollpins provided can be installed using the 7/16" punch. Alternate ...

Shank for the #9 Inversion Shank Assembly. The inversion shank is designed to lift soil from the bottom of the working depth up toward the surface....

Suits the original #9 Hydraulic Recoil assembly (but not the #9v2). Secures the top of the cylinder with a lynch pin 140-0041 and a hairclip 141-00...

30mm diameter pin to secure the top of the hydraulic cylinder in the #9v2 shank assembly. Suits the Hydraulic Cylinder 3" Bore (153-4217).

Shearpin and clips to suit the #9 Rigid Shank Assembly. This shearpin is suitable for the AP71, AP72, AP81, AP91 and AP92 model rigid shank assembl...

Shearpin and clips to suit the #9 Rigid Shank Assembly. This shearpin is suitable for the AP51 model or 150x150mm RHS Rigid Shank Assemblies and ha...

Shear pin and clips to suit the Econo Rigid shank assembly. Fits the 4"x4" Econo Rigid Shank carrier 004-3001. *Old Part No. 141-017

This accumulator clamp suits both 10L and 20L accumulators. Alternate Part No.154-488  

Toolbox to be attached to a plough, contains spare parts for a plough.

Rear tow hitch for the Agrowplow AP11. A rear tow hitch enables trailing machines to be hitched to the rear of the seed drill, including the Rubber...

  The rear tow hitch allows trailing implements to be hitched safely to the rear of the ripper and provides the facility for it to be connected via...

Bearing housing to suit bearings with outer diameter of 52mm, as found on the 15 notch disc assembly. Fits 138-3025

Two-piece bearing housing used to secure the 25.4mm spherical bearing to the Agrowdrill. Commonly found on older Agrowdrill models.The distance bet...

Bearing with ID 5/8" and OD 52mm. Mounts into 110-4112 bearing housing. *Old Part No. 138-325

Sealed bearing, fits on a shaft 25mm and into hub or housing of 62mm in diameter. ID 25mm, OD62mm. Cylindrical. *Old Part No. 138-031

The Spherical Bearing is used on the #9 hydraulic Swing Arm and is Teflon-lined for grease-free maintenance. It has an OD of 62mm and an ID of 40mm...

Blade to suit #1 Shank. This blade requires the use of the #1 Blade Adaptor to attach to the Shank. This blade comes plain with no wear-reducing en...

Blade to suit #1 Shank. This blade requires the use of the #1 Blade Adaptor to attach to the Shank.It has been hard-faced on all leading edges and ...

Blade to suit #1 Shank. This blade requires the use of the #1 Blade Adaptor to attach to the Shank.It comes with 4 x tungsten tiles across the lead...

Blade Narrow to suit the #7 Shank. The narrow blade does not use a blade adapter but fits directly to the shank and is supplied with the required h...

Blade Narrow to suit the #7 Shank. The narrow blade does not use a blade adapter but fits directly to the shank and is supplied with the required h...

Blade Narrow to suit the #7 Shank. The narrow blade does not use a blade adapter but fits directly to the shank and is supplied with the required h...

Blade to suit #7 Shank. This blade requires the use of the #7 Blade Adapter to attach to the Shank. A knock-on tool for the safe installation of th...

Blade to suit #7 Shank. This blade requires the use of the #7 Blade Adapter to attach to the Shank. A knock-on tool for the safe installation of th...

Blade to suit #7 Shank. This blade requires the use of the #7 Blade Adapter to attach to the Shank. A knock-on tool for the safe installation of th...

Heavy-duty blade to suit the #8 shank.This GP blade comes with 3 x heavy-duty rock teeth across the leading edge of the blade as well as additional...