ALL STATES & TERRITORIES
Used in the #9 Assemblies.
1.1/4" diameter pin, 5" working width. Pin suits the #8 shank and #1 shank hydraulic recoil assemblies. See 120-0001, 120-0003, 120-0007, 005-10...
View full detailsCurrent hydraulic cylinder for the #9 Hydraulic Shank Assembly. Has a 3" bore and 9" cylinder rod displacement. Pin-eye cylinder bush is 30.2mm str...
View full detailsFabricated part equivalent to 154-0016. Used on hydraulic cylinder 153-4208 in tandem with brass flow restrictor USE 154-0016
Hydraulic jump cylinder for the Agrowplow #1 and 8 hydraulic shank assemblies. Has a 2.1/2" bore and a 9" rod displacement.
Suits #9 hyd shank
Hydraulic stroke control segments stop the hydraulic cylinder from closing by increments. On a phasing set, only the drive cylinder needs to be con...
View full detailsThis idle shaft is made out of 25.4mm (1") Stainless steel and is 315mm long. It has a key-way machined in the entire length of the shaft for secur...
View full detailsWear plates protect inclusion plates from damage through repeated use, increasing their lifespan. Wear plates are sold individually; two plates ar...
View full detailsInclusion plate with wear plates. Wear plates can be easily replaced saving huge cost in material and time. Designed for the #9 shank and may suit ...
View full detailsSplitter plates for the #9 Inversion Shank Assembly. The inversion shank is designed to lift soil from the bottom of the working depth up toward th...
View full detailsHollow Bar 75 / 45
Bush to suit Agrowdrill Levelling Tube
This lynch pin has an 11mm pin and is designed to fit into clevis pins. Alternate Part No.140-039
11mm pin which secures a shaft of up to 42mm diameter. Old Part Number 140-041
Mechanical Depth Stop to suit the cylinders on the AD230, AD240 and the AD140.
Replacement blade for the Mulch Blade Assembly (123-0001). Mulch blades are used to cut plant roots near the surface. The blades are reversible and...
View full detailsPart of the mulch blade assembly 123-0001, this clamp secures to the side of the #8 or #9 Shank Assembly and holds the blade 122-2002. Old part no...
View full detailsPart of the mulch blade assembly 123-0001, this clamp secures to the side of the #8 or #9 Shank Assembly and holds the blade 122-2002. Old part no...
View full detailsThe mulch blade assembly mounts two blades to rigid or hydraulic #8 and #9 Shank Assemblies. They strike out from the side to cut plant roots near ...
View full detailsZinc-plated hex nut to suit M16 coarse thread with a 2.0mm Pitch
35mm shaft. Hub, 107.9mm PCD with 5 studs. Supplied with M20 Castle Nut, Washer ID20/OD45/6mm, Hub cap, Bearing Spacer ID35/OD45/6mm
This clevis pin is 25.4mm in diameter and has an overall useable length of 87mm. Designed to have a lynch pin fitted through to secure the pin from...
View full detailsSpring jump pivot clamp to suit 100mm or 4" RHS. Suits the #8 spring jump shank models. Also known as a carrier plate. *Old Part No. 003-101
Spring jump pivot clamp to suit 100mm or 4" RHS. Suits the #7 spring jump shank assembly. Also known as a carrier plate. Old Part No. 001-102
Coulter assembly to suit ploughs with #9 Shank Assemblies with hydraulic breakout. The coulter assembly is supplied with mounting hardware to fit ...
View full detailsAttach coulters to your plough to help break through the trash. Suits the hydraulic recoil assemblies for the #8 and #8-9 hybrid shank. For rigid s...
View full detailsAttach coulters to your plough to help break through the trash. Suits the rigid shearpin breakout assemblies for the #8 and #8-9 hybrid shank. For ...
View full detailsPRESSURE GAUGE FOR ACCUMULATOR
Punch specifically designed to remove worn bushes and insert the steel-backed teflon bushes into the #9 Shank.