Products

This bush has been superseded by the steel equivalent 006-4019 Industrial application plastic bush designed for wear with resistance to dust and d...

Industrial application plastic bush designed for wear with resistance to dust and dirt exposure. Lubrication and maintenance-free bush. Used in see...

Industrial application plastic bush designed for wear with resistance to dust and dirt exposure. Lubrication and maintenance free bush. Used in som...

Industrial application plastic bush designed for wear with resistance to dust and dirt exposure. Lubrication and maintenance-free bush. Used in som...

Clip secures the #9 blade onto the #9 shank. Not required if your #9 shank has a roll pin hole. AUSPRING INDUSTRIES PTY LTD sku 21522A

Calibration handle to suit the AD230 Seed drill. It comes zinc plated and assembled with plastic piping installed.

Half link to suit chain 08B. Also see joiner link 115-7011. *Old Part No. 115-710

Joiner link to suit chain 08B. Also see half link 115-7010. *Old Part No. 115-711

SKF Carbon steel drive chain. Comes in a 3m length. Half link or joiner links may be required.Some sprocket drive assemblies also utilise an 08B du...

SKF Carbon steel drive chain. Comes in a 3m length.  ANSI Chain Size: 08B-2 Strands: Single Pitch (mm): 12.7 or 1/2" A single 08B chain can be...

Joiner link to suit 10B chain. Alternate Part No.137-160

SKF Carbon steel drive chain. Comes in a 3m length. Joiner links may be required. ANSI Chain Size: 10B-1 Strands: Single Pitch (mm): 15.875 or 5/8"...

This clutch chain guide is 40mm long, made out of 50mm OD nylon and has a 9mm hole drilled through the centre. Alternate Part No.385-480

Chain Tensioner Block made out of 50mm engineering plastic and tapped with a M10 hole

This chain tensioner is made out of a 30mm nylon shaft and is 32mm long.

Mild steel welded part. Chain tensioner used in seed drill drive assemblies to secure the nylon chain tensioner in position.

#1 rigid shank pivot clamp

Cat 3 RHS Lift Arm Mount Clamp This clamp is used in tandem with Bottom Tow Lug (113-3023) to clamp around 100x100 RHS and form a single Cat-3 link...

Clamping bracket to suit the #8 shank assemblies. Suits 150x150mm (6x6") RHS frame. Assembled in tandem with 005-1008.

Clamp Plate used as part of the #1 Rigid Shank Assembly (120-0015 and 120-0002) and #8 Hydraulic Shank Assembly (120-0003). The plate clamps the as...

Old Part 110-3047

Alt. Part SKU 116-319

Suits all Agrowdrills with electric clutch *Old Part No. 160-433

This is a roller component in the clutch assembly. It is machined out of 65mm diameter self-lubricated engineering plastic and has an overall lengt...

Alt. Part SKU 116-417

Alt. Part SKU 132-225

25mm coil tyne used as part of the Agrowdrill 325 Coil Tyne assembly on ADx20 series Agrowdrill direct drills. Use point adaptor 115-4009 to fit b...

25mm coil tyne designed for the Agrowdrill 425 Coil Tyne assembly. Suits AD083, AD130/140, AD230/240 Agrowdrills. Made in Australia. Download: Pa...

25mm coil tyne that forms part of the 700 Coil Tyne assembly. Requires the 700 baker boot point. Suits single bolt points with 7/16 x 2-1/2 bolts....

Heavy duty coil tyne used in the 732 Coil Tyne Assembly. The coil has a 32mm diameter and suits the 732 baker boot point.  Made in Australia

This tyne suits the Self-Aligning Coulter (SAC) Assembly. It mounts to 100x100 RHS using the standard coil tyne clamp 115-3009. The right-hand ori...

Control arms used in the #1 and #8 Hydraulic Assemblies *Old Part No. 125-352