Agrowplow

Replacement blade for the Mulch Blade Assembly (123-0001). Mulch blades are used to cut plant roots near the surface. The blades are reversible and...

Part of the mulch blade assembly 123-0001, this clamp secures to the side of the #8 or #9 Shank Assembly and holds the blade 122-2002. Old part no...

Part of the mulch blade assembly 123-0001, this clamp secures to the side of the #8 or #9 Shank Assembly and holds the blade 122-2002. Old part no...

The mulch blade assembly mounts two blades to rigid or hydraulic #8 and #9 Shank Assemblies. They strike out from the side to cut plant roots near ...

Alt. Part SKU 134-130

Alt. Part SKU 134-090

Zinc-plated hex nut to suit M16 coarse thread with a 2.0mm Pitch

Old Number 134-1053

35mm shaft. Hub, 107.9mm PCD with 5 studs. Supplied with M20 Castle Nut, Washer ID20/OD45/6mm, Hub cap, Bearing Spacer ID35/OD45/6mm

This clevis pin is 25.4mm in diameter and has an overall useable length of 87mm. Designed to have a lynch pin fitted through to secure the pin from...

Spring jump pivot clamp to suit 100mm or 4" RHS. Suits the #8 spring jump shank models. Also known as a carrier plate. *Old Part No. 003-101

Spring jump pivot clamp to suit 100mm or 4" RHS. Suits the #7 spring jump shank assembly. Also known as a carrier plate. Old Part No. 001-102

Coulter assembly kit to suit ploughs with #9 Shank Assemblies with hydraulic breakout.  Coulters mount to the shank assembly ahead of the shanks, b...

Attach coulters to your plough to help break through the trash. Suits the hydraulic recoil assemblies for the #8 and #8-9 hybrid shank. For rigid s...

Attach coulters to your plough to help break through the trash. Suits the rigid shearpin breakout assemblies for the #8 and #8-9 hybrid shank. For ...

Coulter assembly to suit ploughs with #9 Shank Assemblies with rigid and hydraulic breakout. Coulters are available with either 12" or 14" plain di...

PRESSURE GAUGE FOR ACCUMULATOR

Punch specifically designed to remove worn bushes and insert the steel-backed teflon bushes into the #9 Shank.

Punch specifically designed to secure the 12mm roll pin 140-4087 and 4077 into the #9 Blade. This punch is made out of 4140 steel and has been hard...

Punch specifically designed to secure the 7/16" roll pins into the #9 Hydraulic Shank Assembly. This punch is made out of 4140 steel and has been h...

Hydraulic hose kit for the AP31 rear tow hitch. Requires 560-2011 or 560-2010. Comes with 3/8" hose, 3/4" JIC female ends (T204-0612), and mounting...

The rear tow hitch attaches to 200x200 RHS frames and is suitable for Agrowplow deep ripper models AP71, AP81, and AP91. It allows for a trailing i...

Hydraulic lines for AP71 rear tow hitch. Requires 562-2012 Rear Tow Hitch AP71 AP81 AP91. Hydraulic lines are required for Flexirollers with hydrau...

Hydraulic lines for AP81 and AP91 rear tow hitch. Requires 562-2012 Rear Tow Hitch AP71 AP81 AP91. Hydraulic lines are required for Flexirollers wi...

Suits the #8 and #1 Hydraulic Shank Assembly

Pin fits in a 12mm hole and is 55mm long.

This rollpin measures at 11.11mm in diameter, is 57.15mm long and is used in the #9 hydraulic assembly on the Dogbone pin and on the Hydraulic Pivo...