Agrowdrill

Simplex sprocket, suits 08B chain with 24 teeth. Sprocket secures on a 20mm shaft with grub screws. Model SKU: 630-4110; Chain: 08B; Teeth: 24; Sha...

Simplex sprocket, suits 08B chain with 27 teeth. Sprocket fits to a 20mm shaft and secures with grub screws. Identical to part 630-4119

Simplex sprocket, suits 08B chain with 60 teeth. Sprocket fits to a 20mm shaft and secures with grub screws.

24 Tooth Simplex sprocket to suit a 10B Chain. It has been machined out to suit a 60mm shaft. Predominately used on the AD95. Alternate Part No. 11...

36T PRIMARY DRIVE SPROCKET primarily used on the JPC2000. This sprocket is driven by a 10B chain.

Fabricated fixed idler sprocket. Suits 08B chain with two 21 tooth sprockets. Sprockets secure with grub screws to a 25.4mm shaft.

Dust cap or Hub cap to suit the 50 series hub used on the AD130.

Tension spring used in the current AD140 drive assembly. It is made out of 6.3mm Wire Gal, has an OD of 59mm and has around 28 total coils. This sp...

Chain tensioner made in engineering plastic, outer diameter 30mm, 50mm long. Supplied with nut to secure in drive assembly. *Old Part No. 124-485

Chain tensioner made in engineering plastic, outer diameter 30mm, 55mm long. Supplied with nut to secure in drive assembly.

Chain tensioner made in engineering plastic, outer diameter 30mm, 75mm long. Supplied with nut to secure in drive assembly.

Chain tensioner made in engineering plastic, outer diameter 40mm, 105mm long.

Chain tensioner made in engineering plastic, outer diameter 40mm, 135mm long.

Chain tensioner made in engineering plastic, outer diameter 30mm, 50mm long. Equivalent Part No. 124-4085

Chain tensioner made in engineering plastic, outer diameter 50mm, 40mm long. Supplied with nut to secure in drive assembly. *Old Part No. 124-484

Nylon chain tensioner cut from 70mm rod. Used on seed drill assemblies including the 13 and 18 run Agrowpdrills and the 3000 and 3400 seed drill mo...

(x2) offsets are required to update an AD230. This is intended to shift the front tynes forward by 150mm in the case that the tyne is fitted with d...

Top cylinder pin commonly used on the 3000 series Agrowdrill. It is made out of a 25.4mm bright shaft, is 250mm long and comes with two holes drill...

Jumbo Top Link, 1 3/8" UNC THREAD Dia. CAT2 Eyelets 1" BallEnd Adjustment range 63cm to 91cm (24.75" to 35.75")

 Complete parts set for the 325 Tyne Assembly. The assembly includes coil tyne, a clamp to suit 100x100mm RHS, seed boot, and baker boot point.  S...

Complete parts set for the 425 Tyne Assembly. Includes tyne, tyne clamp, seed boot, and baker boot point with tungsten tile.  Fits the Agrowdrill...

The 700 Coil Tyne was a tyne assembly used on earlier model Agrowdrills, including the AD3000, ADx00 series drills, and JPC 2000. It used a 25mm co...

The 732 Coil Tyne Assembly is a heavy-duty tyne assembly used on some older model Agrowdrill direct drills, including the AD3000, ADx00 series mach...

Fastener kit for the 732, 700, 425, and 325 tyne assemblies. Used to secure the tyne bolt clamp (115-3009). Includes an M16x200 bolt, plus a nut an...

Tyne clamp used as part of a tyne clamp assembly to secure Agrowdrill tynes to the machine toolbar. Suits 100mm x100mm RHS, for all 25mm coil sprin...

Suits 732 tyne

M12 U-Bolt to secure to 50x50 RHS, galvanised with 62mm hole centres. Used on the AD130, AD230 and AD730 to secure the small seed box down tube b...

This M16 U-Bolt is grade 8.8 and is used to secure to 100x100 RHS. It has 55mm of working thread and an overall length of 152mm from the inside fac...

M20 U-Bolt to secure to 100x100 RHS. Used on the AD230 rear tow hitch. Passivated parts may be supplied with zinc plating and vise versa.

M20 U-Bolt to secure to 100x195 RHS. Passivated parts may be supplied with zinc plating and vise versa.

Uni-Hub 1 assembly. Includes hub, cap, washer, nut, and split pin. The Uni-Hub 1 is a 5-stud 37mm hub with 107.9mm PCD. 

35mm shaft. Hub, 107.9mm PCD with 5 studs. Supplied with M20 Nylock Nut, Washer ID20/OD45/6mm, Hub cap. Dust cap part number 161-0101

This dust cap fits the 401 disc assembly and covers the end of the bearing hub where it mounts through the disc.

35mm shaft. Hub, 107.9mm PCD with 5 studs. For the full assembly including castle nut and hub cap see part 161-0004. This component is the hub with...

35mm shaft. 95mm PCD with 5 studs Supplied with Hub, Wheel Nuts, Studs Collar and Dust Cap, M20 Castle Nut, Washer, Bearing, Seal Ring and Circli...

Includes Hub, Studs, Nuts, Circlip and Bearing Lug nut 161-0138

The varibox is a self-contained gearing system that allows an Agrowdrill operator to have greater control over the flow of seed through the main se...

The varibox is a self-contained gearing system that allows an Agrowdrill operator to have greater control over the flow of seed through the main se...

The varibox is a self-contained gearing system that allows an Agrowdrill operator to have greater control over the flow of seed through the main se...

Welded assembly for the AD720 and AD120 seed drill drive, secures to the varibox. *Old Part No. 124-447

Special washers made for the seed box on Agrowdrills. Used on the gate arms and varibox adjustment arms.

Zinc Plated/Passivated flat washer to suit M16 nuts and bolts.