Agrowdrill

Supplied with bearing 138-4020.

This sprocket clutch assembly comes with 2 bearings installed to suit a 1" shaft (25.4mm). The overall length of the assembly is 110mm. The length ...

Sprocket clutch 30/21T with bearing 138-1100.

Simplex sprocket, suits 08B chan with 30 teeth. Sprocket secures to a 50mm shaft with both key way (14mm) and grub screws (M8). This part supersede...

Sprocket with two sets of 36 teeth designed for 10B chain. Includes bearing 138-4052.

Sprocket with 30 and 36 teeth that suits the DF1000. Includes bearing 138-4051.

Plate sprocket to suit 08B chain with 30 teeth. Suits seed drill clutch assembly. Old Part No. 660-413

Simplex sprocket, suits 08B chain with 14 teeth. Sprocket secures with grub screws to a 25mm shaft. Suits ADx30 series Agrowdrills. Model SKU: 115-...

Simplex sprocket, suits 08B chain with 15 teeth. Sprocket secures with grub screws to a 25mm shaft. Suits the JPC2000.

Simplex sprocket, suits 08B chain with 20 teeth. Sprocket secures with grub screws to a 50mm shaft. Model SKU: 630-4111; Chain: 08B; Teeth: 20; Sh...

Simplex sprocket, suits 08B chain with 21 teeth. Sprocket secures with grub screws to a 20mm shaft. Old Part No. 115-420 Model SKU: 115-4020; Chain...

Simplex sprocket, suits 08B chain with 21 teeth. Sprocket secures with grub screws to a 25.4mm shaft. Old Part No. 113-451 Model SKU: 113-4051; Cha...

Simplex sprocket, suits 08B chain with 24 teeth. Sprocket secures on a 20mm shaft with grub screws. Model SKU: 630-4110; Chain: 08B; Teeth: 24; Sha...

Simplex sprocket, suits 08B chain with 60 teeth. Sprocket fits to a 20mm shaft and secures with grub screws.

24 Tooth Simplex sprocket to suit a 10B Chain. It has been machined out to suit a 60mm shaft. Predominately used on the AD95. Alternate Part No. 11...

36T PRIMARY DRIVE SPROCKET primarily used on the JPC2000. This sprocket is driven by a 10B chain.

Fabricated fixed idler sprocket. Suits 08B chain with two 21 tooth sprockets. Sprockets secure with grub screws to a 25.4mm shaft.

Tension spring used in the current AD140 drive assembly. It is made out of 6.3mm Wire Gal, has an OD of 59mm and has around 28 total coils. This sp...

Chain tensioner made in engineering plastic, outer diameter 30mm, 50mm long. Supplied with nut to secure in drive assembly. *Old Part No. 124-485

Chain tensioner made in engineering plastic, outer diameter 30mm, 55mm long. Supplied with nut to secure in drive assembly.

Chain tensioner made in engineering plastic, outer diameter 30mm, 75mm long. Supplied with nut to secure in drive assembly.

Chain tensioner made in engineering plastic, outer diameter 40mm, 105mm long.

Chain tensioner made in engineering plastic, outer diameter 40mm, 135mm long.

Chain tensioner made in engineering plastic, outer diameter 30mm, 50mm long. Equivalent Part No. 124-4085

Chain tensioner made in engineering plastic, outer diameter 50mm, 40mm long. Supplied with nut to secure in drive assembly. *Old Part No. 124-484

Nylon chain tensioner cut from 70mm rod. Used on seed drill assemblies including the 13 and 18 run Agrowpdrills and the 3000 and 3400 seed drill mo...

(x2) offsets are required to update an AD230. This is intended to shift the front tynes forward by 150mm in the case that the tyne is fitted with d...

Top cylinder pin commonly used on the 3000 series Agrowdrill. It is made out of a 25.4mm bright shaft, is 250mm long and comes with two holes drill...

Jumbo Top Link, 1 3/8" UNC THREAD Dia. CAT2 Eyelets 1" BallEnd Adjustment range 63cm to 91cm (24.75" to 35.75")

 Complete parts set for the 325 Tyne Assembly. The assembly includes coil tyne, a clamp to suit 100x100mm RHS, seed boot, and baker boot point.  S...

Complete parts set for the 425 Tyne Assembly. Includes tyne, tyne clamp, seed boot, and baker boot point with tungsten tile.  Fits the Agrowdrill...

The 700 Coil Tyne was a tyne assembly used on earlier model Agrowdrills, including the AD3000, ADx00 series drills, and JPC 2000. It used a 25mm co...